Take the same precautions as for oil to keep Waxoyl off your skin. Ensure suction cups are protected from damage during storage. Before starting the engine make sure the others are clear of the danger areas; examples of danger areas are: the rotating blades and belt on the engine, the attachments and linkages, and anywhere beneath or behind the machine. Do not wear a necktie or scarf. It is expected that components will be cleaned and lubricated where appropriate, and that any opened hose or pipe connections will be blanked to prevent excessive loss of hydraulic fluid and ingress of dirt. Chock both sides of all four wheels.
Cut-Out Knife - used to remove broken glass. Do not operate a machine which is defective or has missing parts. An understanding of the material contained in this manual and in the appropriate Dealer Service Bulletins will help technicians to better serve vehicle owners. Contact your nearest fire department as quickly as possible. Hubs when when applicable Axle Oil Limited Slip Diff. Do not refuel with the engine running.
Waxoyl can take a few weeks to dry completely. Do not use your fingers to check for hydraulic fluid leaks. Used fluoroelastomeric components whose temperatures have not exceeded 300°C require no special safety precautions. Do not weld near the affected area during the drying period. Do not use petrol, diesel fuel or paraffin to clean your skin. Where a torque setting is given as a single figure it may be varied by plus or minus 3%.
Do not weld cast iron. Apply in a well-ventilated area. Keep flames away when applying Waxoyl. Replace unreadable or missing decals with new ones before operating the machine. Hydraulic Fluid Fine jets of hydraulic fluid at high pressure can penetrate the skin. Wear protective clothing to suit the job. Make sure the maintenance procedures in this handbook are completed before using the machine.
Beats dealing with greasy paper manuals!!!!! This oil should be drained after the first 100 hours operation and the engine filled with the appropriate recommended grade as shown in the lubrication chart. Before working under raised loader arms, fit the loader arm safety strut. Renew whenever disturbed unless otherwise instructed. Before disconnecting or connecting hydraulic hoses, stop the engine and operate the controls to release pressure trapped in the hoses. Hydraulic Hoses Damaged hoses can cause fatal accidents. The front axle serial number is stamped on a plate mounted on the axle. S145300 Syncro Shuttle Serial Plate The Syncro Shuttle serial number is stamped on a label which is mounted to the rear face of the unit.
Always use barrier cream or wear gloves to prevent skin contact. Do not use a machine with a frozen battery. Firefighters should use self-contained breathing apparatus. Apply in a well-ventilated area. Components for Excavator Valve Block A.
Do not check the battery charge by shorting the terminals with metal; use a hydrometer or voltmeter. Make sure any defects found during the regular maintenance checks are rectified immediately. Do not smoke or touch food while handling this lubricant. To remove the cap; turn it to the first notch and let the system pressure escape, then remove the cap. New fluoroelastomeric components at ambient temperature require no special safety precautions. If a leak is evident find the source and repair as required. Never work under a machine on soft ground.
Ensure the other end is securely chocked. To protect your eyes, wear goggles when using a wire brush to clean components. Make sure that lifting equipment is strong enough for the job. This will protect against eye injury from components accidently flying out. Do not rely solely on the machine hydraulics or jacks to support the machine when working under it. This Service Manual has easy-to-read text sections with top quality diagrams and instructions. Clamp Clamp Spoo pool Clam lamp Spoo Spooll Clamp Clamp Ha Hamw mwor orth thy y A.
Stop greasing when fresh grease appears at the joint. Do not use water to put out a machine fire, you could spread an oil fire or get a shock from an elecrical fire. Always connect the negative pole of the battery to earth. Make sure that lifting tackle complies with all local regulations and is suitable for the job. Exhaust Gases Gases Breathing the machine exhaust gases can harm and possibly kill you. Do not handle used engine oil more than necessary.
Use the step s and handrails. If you will be working with other people, make sure any hand signals that may be used are understood by everybody. Get out of the cab into fresh air. But when it is carelessly operated or poorly maintained it can become a danger to you the operator and others. Use carbon dioxide, dry chemical or foam extinguishers. Always chock the wheels at the opposite end of the machine that is to be jacked.