We also dig the race car look that you get when your run a set of seat harnesses in your ride. What should I look for? So go back to that dealer if there is no other one around and them. All vehicles built before then is life time. Fits Model with Automatic Seat Belt Retractors. With the seatbelt extended all the way out, yank really hard and see if it catches. Do not rely on the name of your existing carpet to match a color we offer. The seat belt that comes factory on your car is not designed for super high-speed encounters per se; rather it's designed for normal driving conditions.
Performing this conversion is done at your own risk. The graphite grease from the track gums up the position switch and the seat belt computer does not know where the belt is. Overview: The 240sx convertible, built from 1992 to 1994, started life as a leftover 240sx base coupe. The seat is connected to the chassis by four mounting locations. Then I opened the door and nothing, it just sat there. Next, cut a slot in your rear side panel somewhat of a slight angle as shown here.
I used the rear because the seatbelt would be straight out when buckled up. It should come out pretty easily. A Dremel with a reinforced cutoff wheel works great. Nissan is only responsible to make parts for cars ten years after their production. From what i read from this forum, i can just go to a nissan dealership and ask them if they can change it for free? And about how much would it cost to do it? One of the best ways to improve the safety of your vehicle is by adding a pair of Nissan 240sx seat harnesses. Once it has been fully extended out and mounted correctly, it will not lock up like it used to when it was retracted all the way. Rearmost bolt is not shown, top is behind seatbelt.
My second question is that if no nissan dealership has the parts, what are the other alternatives to Safety? Now take the bottom mounting bracket other end of seatbelt mechanism and put it through the carpet hole where the lap belt used to reside. Try to locate a L or R on the manual seatbelt to find out which side it belongs to. A hacksaw blade held by hand works great here, as you can lay it flush and cut it off smooth. This may be a long shot but I'm pretty sure those seat belts have a lifetime warranty. Material may not be copied or reprinted without written permission. Inventory changes often so if you don't see the seat belts that you need we can help you find it when you complete our.
I may have trouble explaining this, but bear with me: Now find out which each manual belt assembly belongs to. Buckle mounting bolt might have to be enlarged and seatbelt chassis harness must be bridged. But in the S14, the actual mechanism faces towards the center of the cabin. Rear is surged on three sides. Andy's Auto Sport is the ultimate shopping destination for your Nissan 240sx seat harness needs! The seat belts are easy to remove. From 1989-1994 the 240sx were all the same, however I found out the hard way that some of the parts from different trim models are not 100% compatable. Instructions: Details: Rating: Rating 4.
There is also a chassis harness connector under the seat, disconnect it. If your manual seat belts locked after completely rolled up: 1. The color of the samples below may vary, depending on the calibration of your monitor. I also read about a recall about the seatbelt clips. The A-Pillar has to be removed to remove the Sliding Mechanism. I told him I was pretty sure it was still under warranty.
Whether you drive your car on the street or at the track, safety should always be a top priority. So I did R with L and vice versa. It helps if you grind down the little nubs on the back side, as the rear panels are not as flexible as the fronts. Put the door sill back on, reinstall the A-Pillar mounting bracket on 3-12mm bolts. I recommend reupholstering your existing seats! This item is custom made after the order is placed, and typically ships within 2 business days.
Now just lift the carpet away from the lap seatbelt and start removing the two 14mm bolts. I checked the micro switch at the end of the track. My second question is that if no nissan dealership has the parts, what are the other alternatives to Safety? However, now vehicles are truly safety cages and numerous studies have proven that a good seat belt system is the best way to survive an accident. Least you can't just change the bulbs. Brought my car to Nissan dealership they said it was gonna be 98 dollars to find out the problem blah blah blah, so i have them do it and it ended up being a micro switch according to the mechanic which was gonna cost another 30 bucks plus what ever labor costs. Q: Why buy a seat harness? In order to access the other parts Lap Belt, Belt for automatic seatbelt mechanism you need to pull the carpet which means you have to pull out the seat.