This will give you much more room to work, but it will still be a bit cramped. Order your new headlights from AutoZone and rely on trustworthy advice from our knowledgeable staff whenever you visit your local store. Changing both headlight bulbs on your Jetta at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. All you have to do is simply use a regular cut polish from any auto parts store and you can make the headlight lens look shinier. First there is a plastic cover that has to be removed. That took about 5 seconds.
Both of these must be removed for the headlamp assembly to be pulled forward. The Front Turn Signal bulb is located at the bottom inner corner of the headlight housing. Headlight Change 1999 I took me some time to get this done because it was the first time for me and I wasnt sure this was right or not. All bulbs have this O-ring but the Hella model I had was just too big. But if it's only loose, carefully tighten it to adjust it. If necessary, you may also use any other miniature wedge base bulbs such as the , 158, , W5W or a brighter unit. But first, you have to know if it's faulty.
Be careful, as the old bulb is still plugged in to the socket, and you will be pulling both out together. If you do get the new bulb dirty, wipe it clean with an alcohol moistened paper towel. Note: I am not a registered charity. There is three little grooves that the bulb fits into, to ensure correct placement. Also, inspect the wirings if you need to replace any of them.
Have this replaced immediately because it's quite difficult to drive with only one functioning headlight. There are some white plastic pegs pointing inward towards the socket. This side is the same as the passenger side but has very little room due to the battery cover. OnceI did that I was able to properly seat the bulb note: Aligning thethree little grooves is very important. Changing both headlight bulbs on your Jetta at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side.
This is quite foreseeable because of the different road conditions that you take. To create this article, 10 people, some anonymous, worked to edit and improve it over time. Now is the time to clean up the mess around the fender where the headlight mounts. Pull the black plastic power plug straight off the base of the old high beam bulb. The video above shows you to replace the headlight in your 2010 Volkswagen Jetta. Behind this cover, in between the battery and the headlight, you will see a black rectangular box being held by a pressure clip. Sometimes, if the headlight bulbs don't light up, it's because of disconnected wires.
Locate the headlight assembly at the front of the vehicle. Driving with malfunctioning headlights can be very dangerous. Clean a clouded headlight assembly. The chamber that houses the socket is made of white plastic, has wires connected to it, and serves as the walls that the socket twists into see pic. Push the black rubber dust cap in place over the high beam bulb. Check if the wirings are still functioning. Headlight Change 1999 Push the casing back in and lock the casing in with the lever.
It's attached by 2 Phillips screws. In most states, driving with burnt-out headlights can result in a fix-it ticket. In some Volkswagens, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb and vise versa. The impurities and heat from your fingers could irreparably damage and kill your bulb. All of the parts carried on Go-Parts. Believe me the nightbreakers are way better. Go buy the new bulb.
Well, since there are no visible screws anywhere around, how do I get the headlight out? Busted wiring harness If you've replaced the headlight bulb, but the assembly still refuses to function, it could mean that the wiring harness is damaged. Here are some troubleshooting tips that you can use to find out. You may have to push pretty hard to release the clips. Do one side first, so you can use the other side as a reference. Faulty bulbs A common reason why the headlight assembly fails is because the headlight bulb is no longer functioning. Item in Good Condition Guaranteed If the part we ship to you arrives in damaged or non-working condition, we will ship another item out to you immediately. However this slide mechanism is very tough to move the first time.